HOME
ABOUT
NEWS
PRODUCT
SUPPORT
FEEDBACK
CONTACT
简体中文
Support each other can overcome the challenge
Solidarity and Coordination can create the future together
Pressure Gauge
Pressure Gauge
Pressure Transmitter
Flow Meter
Ultrasonic Flow Meter
Electromagnetic Flow Meter
Turbine Flow Meter
Vortex Flow Meter
Rotameter
Swirl Meter
V-shape Cone Flow Meter
Verabar Flow Meter
Throttling Device
Level Meter
Level Gauge
Level Switch
Master Meter
Pressure Calibrator
Temperature Calibrator
Temperature Gauge
Imported Product
AMETEK
PIZZATO
Valve Series
Valve Series
Control Valves
Manual Valves
Actuator
Cut-off Valves
41
Close
流量物位仪器专业制造商-上海爱伊爱弟科技有限公司
Product Category
Pressure Gauge
Pressure Gauge
Pressure Transmitter
Flow Meter
Ultrasonic Flow Meter
Electromagnetic Flow Meter
Turbine Flow Meter
Vortex Flow Meter
Rotameter
Swirl Meter
V-shape Cone Flow Meter
Verabar Flow Meter
Throttling Device
Level Meter
Level Gauge
Level Switch
Master Meter
Pressure Calibrator
Temperature Calibrator
Temperature Gauge
Imported Product
AMETEK
PIZZATO
Valve Series
Valve Series
Control Valves
Manual Valves
Actuator
Cut-off Valves
HOME
≡
Master Meter
≡
Pressure Calibrator
≡
A+E YFQ-60TS Pressure Pump(Table)
PRODUCT
About us
A+E YFQ-60TS Pressure Pump(Table)
Publish time 2018-01-19 09:26
A+E YFQ-60TS台式压力泵
型号:A+E YFQ-60TS
测量范围:0-60000(kPa)
精度等级:0.5
品牌:AEAD
环境温度:50(℃)
加工定制:是
一、用途
A+E YFQ-60TS压力校验台为新款全不锈钢产品,该校验台与标准仪表配合,可以检验一般压力表系列、变送器系列,压力可达60MPa。
二、结构与工作原理
压力校验仪由压力输出接口、油杯、微调、截止阀、连接管路和底座等组成。
使用方法:关闭油杯上截止阀,旋转手摇轮粗微调,使内部活塞移动,由此而产生的压力可传输到两个压力输出接口上的标准仪表和被检定仪表,根据标准仪表显示的压力值对被校验仪表进行校验。
压力校验仪结构:1标准表接口、 2标准接口截止阀、3细微调、4连接管路、⑤输出截止阀、⑥底座。
量程:0-60MPa
接口:M20×1.5
工作介质:变压器油
使用环境:在5~35℃
湿度≤80%,无腐蚀性场所。
三、安装与使用
1 压力校验仪应放在便于操作的工作台上,并须保持水平。
2 压力校验仪不得受到震动,工作台需垫上橡胶皮垫,用螺丝紧固。
3 使用:打开油杯阀门,左旋手轮,使压力泵的汽缸充满变压器油。
4 关闭油杯阀门,旋转手轮,压缩变压器油,使油作用于标准仪表和被检仪表上,根据两台仪表的显示示值进行校验。
四、 维护与修理
1 定期清洗压力校验台各部分。
2 变压器油里不应有杂质或赃物,使用一段时间后,必须更换新油。
3 不用时必须盖上布罩,以免尘埃进入压力校验台内。
上一个:
A+E YQH-DQ......
下一个:
A+E YFQ- 6......